Products from AMX

NI-900 (price: 955,00 €, VAT excluded)


The NI-900 unit is designed to control and automate a variety of devices in single rooms or multiple small rooms and is capable of supporting devices with a variety of communication formats. It is configured to control a limited number of lights, thermostats, video displays and other equipment.

Perfect for single rooms or two or more small rooms with a limited number of devices such as home theaters, MDUs, hotel rooms and other environments.


  • 1 Configurable RS-232 / RS-422 / RS-485 Serial port
  • 3 IR / Serial ports
  • 1 IR Receiver Port
  • 4 Digital I/O ports
  • 2 Communication Networks: AxLink and Ethernet (TCP/IP)
  • 304 MIPS processor speeds
  • 64 MB RAM
  • 32 MB Flash Memory
  • 512 KB Non-Volatile Memory
  • AMX Device Discovery enabled
  • JITC Compliant



  • 1 9/16" x 5 9/16" x 5 1/8" (4.01 cm x 14.10 cm x 13 cm)
  • RU: 1

1.30 lbs (590 g)


  • 300 mA @ 12 VDC
  • Power requirements are usage dependant

Metal with black matte finish

304 MIPS

FCC Part 15 Class B, CE, and IEC 60950


  • Program Port
  • Configuration DIP Switch: Sets the communication parameters for the Program port
  • IR RX LED: Red LED lights when IR data is being received via the rear IR RX port
  • IR LEDs: Three red LEDs light during the transmission of IR or Serial data via the rear IR port
  • I/O LEDs: Four yellow LEDs light when the rear I/O channels 1 - 4 are active. LED indicator for each I/O port reflects the state of that particular port
  • Serial LEDs
  • LINK/ACT: Green LED lights when the Ethernet cable is connected and an active link is established. This LED also blinks when receiving Ethernet data packets
  • Status: Green LED lights when the Controller is programmed and communicating properly
  • Output: Red LED lights when the Controller transmits data, sets channels sends data strings, etc.
  • Input: Yellow LED lights when the Controller receives data from button pushes, strings, commands, channel levels, etc.
  • ID Pushbutton: Sets the NetLinx ID (Device only) assignment for the device


  • RS-232/422/485 (Port 1)
  • IR RX (Port 6)
  • Digital I/O (Port 5)
  • IR/Serial (Ports 2-4)
  • AxLink LED
  • AxLink Port: 4-pin 3.5 mm mini-Phoenix (male) connector provides data and power to external control devices
  • Ethernet Port: RJ-45 port for 10/100 Mbps communication. LEDs show communication activity, connection status, speeds, and mode information: - SPD (speed) - Yellow LED lights On when the connection speed is 100 Mbps and turns Off when the speed is 10 Mbps. - L/A (link/activity) - Green LED lights On when the Ethernet cables are connected and terminated correctly, and blinks when receiving Ethernet data packets.
  • Power Port: 2-pin 3.5 mm mini-Phoenix (male) connector


  • Operating Temperature: 0° C (32° F) to 50° C (122° F)
  • Operating Humidity: 20% to 85% RH
  • Heat Dissipation (Typical): 12.3 BTU/hr


  • 2-pin 3.5 mm mini-Phoenix female PWR connector (41-5025)
  • 6-pin 3.5 mm mini-Phoenix female I/O connector (41-5063)
  • Three CC-NIRC IR Emitters
  • Two 4-pin 3.5 mm mini-Phoenix female connectors (41-5047)


(Click here for larger PDF image) 


    Price: 955,00 €, VAT excluded.



Created by Digiart